Chamberlain CLSS1 User Manual download pdf

Chamberlain warrants to the original purchaser of any

Chamberlain Surge Protector that the surge protector

shall be free of defects in material and workmanship for

a period of one (1) year from the date of original pur-

chase, and will repair or replace, at its option, any

defective surge protector free of charge. The proper

operation of the Chamberlain Surge Protector may

destroy the protector itself. Such an event is not a defect

and is not covered by this limited warranty.

For a period of one (1) year from the date of original pur-

chase of any Chamberlain Surge Protector,

Chamberlain will provide up to $100 to repair or replace,

at its option, damaged garage door opener parts or

components (“Connected Equipment”) which is dam-

aged by a transient voltage surge (an “Occurrence”),

while properly connected through a Chamberlain Surge

Protector to a properly wired AC power line with protec-

tive ground. This limited warranty is null and void unless

all wires leading into the equipment pass through an

appropriate Chamberlain Surge Protector as further

described herein. Chamberlain reserves the right to

review the damaged Chamberlain Surge Protector, the

damaged Connected Equipment and the site where the

damaged occurred. All costs of shipping the

Chamberlain Surge Protector and the damaged equip-

ment to Chamberlain for inspection shall be borne sole-

ly by the purchaser. Damaged equipment must remain

available for inspection until the claim is finalized. The

Chamberlain Surge Protector is not intended for use

with any product(s) other than Connected Equipment.

If you wish to make a warranty claim, please call 800-

528-9131 for instructions. You will need your receipt for

the Chamberlain Surge Protector. All above warranties

are null and void if the Chamberlain Surge Protector in

use during the occurrence is not provided to

Chamberlain for inspection upon Chamberlain’s request

at the sole expense of the purchaser, Chamberlain

determines that the Chamberlain Surge Protector has

been improperly installed, altered in any way or tam-

pered with, Chamberlain determines that the damage

did not result from the occurrence or that no occurrence

in fact took place, or Chamberlain determines that the

Connected Equipment was not used under normal oper-

ating conditions or in accordance with all labels and

instructions.

All Chamberlain Surge Protectors must be plugged

directly into the power source and must not be “daisy-

chained” together in serial fashion with other power

strips, UPS, other surge protectors or extension cords.

Any such installation voids the limited warranty. This

limited warranty only protects against damage to prop-

erly connected equipment where Chamberlain has

determined, in its sole discretion, that the damage

resulted from an Occurrence, and does not protect

against acts of God such as flood, earthquake, direct

lightning strike, war, vandalism, theft, normal-use wear

and tear, erosion, depletion, obsolescence, abuse,

damage due to low voltage disturbances (i. e.

brownouts or sags), non-authorized program or system

equipment modification or alteration. This warranty is

secondary to any existing coverage of any Connected

Equipment, including, but not limited to, any manufac-

turer’s warranty, extended warranties or insurance cov-

erage.

THIS LIMITED WARRANTY IS IN LIEU OF ANY

OTHER WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING ANY IMPLIED WARRANTY OF MER-

CHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE, AND OF ANY OTHER

OBLIGATIONS OR LIABILITY ON SELLER’S PART.

THIS LIMITED WARRANTY DOES NOT COVER NON-

DEFECT DAMAGE, DAMAGE CAUSED BY IMPROP-

ER INSTALLATION, OPERATION OR CARE

(INCLUDING, BUT NOT LIMITED TO ABUSE, MIS-

USE, FAILURE TO PROVIDE REASONABLE AND

NECESSARY MAINTENANCE, UNAUTHORIZED

REPAIRS OR ANY ALTERATIONS TO THIS PROD-

UCT), REPLACEMENT OF BATTERIES AND LIGHT

BULBS OR UNITS INSTALLED FOR NON-RESIDEN-

TIAL USE.

UNDER NO CIRCUMSTANCES SHALL SELLER BE

LIABLE FOR CONSEQUENTIAL, INCIDENTAL OR

SPECIAL DAMAGES ARISING IN CONNECTION

WITH USE, OR INABILITY TO USE, THIS PRODUCT.

IN NO EVENT SHALL SELLER’S LIABILITY FOR

BREACH OF WARRANTY, BREACH OF CONTRACT,

NEGLIGENCE OR STRICT LIABILITY EXCEED THE

COST OF THE PRODUCT COVERED HEREBY. NO

PERSON IS AUTHORIZED TO ASSUME FOR US ANY

OTHER LIABILITY IN CONNECTION WITH THE SALE

OF THIS PRODUCT.

Valid only in the USA and Canada.

114A2915 Rev A Printed in China

Safety

Sensors

To IR sensor

input connectors

Inser

Insert

Wires

Red

White

Gray

Garage Door

SAFETY SENSORS

Garage Door Opener

LIGHTLOCK

Wall

Control

Door

Bell

To wall control

input connectors

Wall

Control

NOTE: The Chamberlain Garage Door Opener Surge Protector is not recommended to be installed with garage door openers manufactured by Marantec America

Corporation or Hoermann, Inc. USA.

RATING CHART / TECHNICAL SPECIFICATIONS

Energy Dissipation:__________________761 joules

Protection Indicator Light:__________________Yes

Catastrophic Surge Circuit:_________________Yes

Thermal Fusing: _________________________Yes

Line Voltage:________________120 VAC, 50/60Hz

Maximum Surge Current:_________________16kA

Maximum Surge Voltage:__________________6kV

Line Current:____________________________15A

Power:__________________________1800 Watts

UL1449 Suppression Rating:______________800V

Protection Modes:________________L-N, N-G, L-G

Before you begin:

It is recommended that you label wires prior to

removing them from the garage door opener. Label

safety sensor wires and wall control wires using

color codes if applicable.

Installing the wall control wires:

• At the garage door opener, remove the wall control

wires from opener terminals, noting polarity and/or

wire color positions.

• Since these wires will now be routed to the surge

protector, use the 5’ piece of white-white/red 24

AWG bell wire (included) as EXTENSION from

surge protector to opener.

• Note polarity/wire colors, twist original wire with

extension wire together, and insert into surge

protector. The terminals colored red and white on

the surge protector are designated for the doorbell

button/wall control wires.

• Attach wires to opener terminals in same order/

color combination as original installation. (Consult

owners manual if necessary).

Installing the safety sensor wires:

• At the garage door opener, remove the safety

sensor wires from opener terminals, noting

polarity and/or wire color positions.

•Since these wires will now be routed to the surge

protector, use the 5’ piece of white-white/black 24

AWG bell wire (included) as EXTENSION from

surge protector to opener.

• Note polarity/wire colors, twist original wire with

extension wire together, and insert into surge

protector. The terminals colored white and gray on

the surge protector are designated for the IR

sensor wires.

• Attach wires to opener terminals in same order/

color combination as original installation. (Consult

owners manual if necessary).

Installing the Surge Protector:

• Plug Surge Protector into AC outlet

• Plug garage door opener into outlet on front of

Surge Protector

•Test garage door opener for proper operation. Be

sure to test all functions including wall control,

keypad, safety sensors (Door Reversal Test - See

garage door opener manual for instructions) and

any other accessories.

Note: After completing installation and restoring

power to the garage door opener, check illumination

of safety sensor LED's (located on safety sensors).

If not illuminated, the wires for the safety sensors

may be crossed at the Surge Protector.

Follow these steps:

1. Unplug Surge Protector and garage door opener

from AC outlet.

2.Verify that the safety sensor wires are connected

to the gray and white terminals on the Surge

Protector. If not, re-wire Surge Protector

following above instructions.

3. If connected to the gray and white terminals and

LED's are still not illuminated, disconnect the

twisted wires from both gray and white terminals

and switch positions. Ensure they are making a

good connection within the terminals of the Surge

Protector.

4. Reconnect AC power to both Surge Protector and

garage door opener.

LED Indicator: The indicator light should be illumi-

nated when the surge protector is plugged into AC

power and is protecting your garage door opener

system. If the indicator light goes out, the surge

protector has sacrificed (depleted) itself to protect

the garage door opener system and should be

replaced immediately.

To protect the door opener low voltage control wires from lightning damage, control wires will be rerouted from the door opener to the surge protector, continuing the

connection to the door opener. This protects the opener’s control wiring.

Model CLSS1

Garage Door Opener Surge Protector

Owner's Instructions:

The Garage Door Opener Surge Protector is designed to protect garage door

openers against damage from lightning and power surges. The Surge Protector

will stop radiated surge currents from coming through wall control and saftey

sensor wires, as well as surge currents from coming through AC power line

according to the rating chart shown below.

Plug the Surge Protector into grounded (3-wire) 120V AC outlet within four (4)

feet of the garage door opener. Plugging Surge Protector into a GFCI (Ground

Fault Circuit Interrupter) is acceptable, but not recommended as power surges

may cause the GFCI to trip and you will need to reset the outlet in order to oper-

ate the garage door opener

WARNING

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Unplug Garage Door Opener from AC outlet and be sure power is disconnected BEFORE installing the Surge Protector.

• Connect terminals ONLY to 24 VOLT low voltage wires.

• The Surge Protector is ONLY for indoor Use.

• DO NOT perform installation during a lightning storm (visible lightning)

FOR TECHNICAL SUPPORT, DIAL OUR TOLL FREE NUMBER: (USA) 1-800-528-9131, www.chamberlain.com

Chamberlain Connected Equipment Limited Warranty

1 2

Model CLSS1 1
ADVERTENCIA 2

Summary of Contents

Page 1 - Model CLSS1

Chamberlain warrants to the original purchaser of anyChamberlain Surge Protector that the surge protectorshall be free of defects in material and work

Page 2 - ADVERTENCIA

Chamberlain garantiza al comprador de cualquierProtector de Sobrecarga Chamberlain que el mismopermanecerá libre de defectos de fabricación y/o demate

Comments to this Manuals

No comments

Chamberlain CLSS1 User Manual

Browse online or download User Manual for Computer Accessories Chamberlain CLSS1. Chamberlain CLSS1 User Manual

Summary of Contents

Comments to this Manuals