Please read this manual and the enclosed safety materials carefully! Fasten the manual near the garage door after installation. The door WILL
9InstallationIMPORTANT INSTALLATION INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUCT
10InstallationSTEP 1 Determine the header bracket locationTo preventpossible SERIOUS INJURY or DEATH:l Header bracketMUST be RIGIDLY fastened to struc
11InstallationSTEP 2 Install the header bracketYou can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow t
12InstallationSTEP 3 Attach the rail to the header bracket1. Position the opener on the garage floor below the header bracket. Use packing material as
13InstallationSTEP 5 Hang the garage door openerTo avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY tostructural su
14InstallationSTEP 6 Install the light bulbsTo preventpossible OVERHEATING of the end panel or light socket:l Use ONLY A19 incandescent (100W maximum)
15InstallationSTEP 8 Install the door bracketFiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFOREinstallation of d
16InstallationSTEP 8 Install the door bracket (continued)OPTION B ONE-PIECE DOORS1. Center the door bracket on the top of the door, in line with the h
17InstallationSTEP 9 Connect the door arm to the trolleyInstallation will vary according to the garage door type. Follow the instructions which apply
18InstallationSTEP 9 Connect the door arm to the trolley (continued)OPTION B ONE-PIECE DOORSIMPORTANT: The groove on the straight door arm MUST face a
1Safety Symbol and Signal Word ReviewThis garage door opener has been designed and tested to offer safe service provided itis installed,operated, main
19InstallationSTEP 10 Install the door controlTo preventpossible SERIOUS INJURY or DEATH from electrocution:l Be sure power is NOT connected BEFORE in
20InstallationSTEP 11 Wire the door control to the garage door openerHARDWAREInsulated Staple(Not Shown)1. Run the white and red/white wire from the d
21InstallationSTEP 13 Install the Protector System®Be sure power is NOT connected to the garage door opener BEFORE installing the safetyreversingsenso
22InstallationSTEP 13 Install the Protector System®(continued)OPTION B WALL INSTALLATIONIf additional clearance is needed an extension bracket (not pr
23InstallationSTEP 14 Wire the Safety Reversing SensorsIf your garage already has wires installed for the safety reversing sensors, proceed to page 24
24InstallationSTEP 14 Wire the Safety Reversing Sensors (continued)OPTION B PRE-WIRED INSTALLATION1. Cut the end of the safetyreversing sensor wire, m
25InstallationSTEP 15 Connect powerTo preventpossible SERIOUS INJURY or DEATH from electrocution or fire:l Be sure power is NOT connected to the opene
26InstallationSTEP 16 Aligning the safety reversing sensorsThe door will not close if the sensors have not been installed and aligned correctly.When t
27AdjustmentsIntroductionWithout a properly installed safetyreversal system, persons (particularly small children) could beSERIOUSLY INJUREDor KILLED
28AdjustmentsSTEP 1 Program the TravelWithout a properly installed safetyreversal system, persons (particularly small children) could beSERIOUSLY INJU
2Test the Wi-Fi®Signal Strength in your garageYou will need a router with Wi-Fi and a smartphone or other mobile device.Make sure your mobiledevice is
29AdjustmentsSTEP 2 Test the Safety Reversal SystemWithout a properly installed safetyreversal system, persons (particularly small children) could beS
30Battery BackupSTEP 1 Install the BatteryTo reduce the riskof FIRE or INJURY to persons:l Disconnect ALL electric and battery power BEFORE performing
31MyQ®Smartphone ControlGet Connected…and control your garage door opener with the MyQ®App.You will need:l A smartphone or tabletl Broadband Internet
32IMPORTANT SAFETY INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.2. ALWAYS keep remote con
33OperationUsing your Garage Door Openerl The garage door opener can be activated with a wall-mounted door control, remote control,wirelesskeyless ent
34OperationDoor ControlSYNCHRONIZE THE DOOR CONTROL: To synchronize the door control to the garage door opener,press the push bar until the garage doo
35OperationMENU OPTIONS (CONTINUED)TIMER-TO-CLOSE (TTC) (Factory default is set to off): The Timer-to-Close feature automaticallyclosesthe door after
36OperationTo Erase the MemoryERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES1. Pressand hold the LEARN button on garage door opener until the learn LED
37MaintenanceMaintenance ScheduleEVERY MONTHl Manually operate door. Ifitis unbalanced or binding, call a trained door systemstechnician.l Check to be
38Diagnostic ChartYour garage door opener is programmed with self-diagnostic capabilities. The UP and DOWNarrowson the garage door opener flash the di
3Carton InventoryYour garage door opener is packaged in one carton which contains the motor unit and all partsillustrated below.Accessories vary depen
39DIAGNOSTIC CODE SYMPTOM SOLUTIONUp ArrowFlash(es)Down ArrowFlash(es)4 5Opener runs approximately 6-8",stops and reverses. Communication error t
40AccessoriesCLLP1953EVCLSS1Laser Parking Assistant:Park in the right spot every time! A laser beam is activated by yourgarage door opener and project
41WarrantyCHAMBERLAIN® LIMITED WARRANTYThe Chamberlain Group, Inc.® (“Seller”) warrants to the fi rst retail purchaser of this product, for the residen
42Repair PartsRail Assembly PartsAccessoriesInstallation Parts13246512NOTICE1342567891011Description Part Number1 Belt 41A52502 Pulley 144C543 Master
1753439682410Repair PartsDescription Part Number1 Sprocket and Sprocket Cover with Screws 041C17512 End Panel with light socket 041D7639-13 Light Lens
4HardwareClevis Pin 5/16"x1-1/2" Ring Fastener (3)Hex Bolt 5/16"-18x7/8" (4)Lock Washer 5/16"-18 (5)Nut 5/16"-18 (6) Se
5AssemblySTEP 1 Assemble the rail and install the trolleyTo preventINJURY from pinching,keep hands and fingers away from the joints while assembling t
6AssemblySTEP 2 Fasten the rail to the motor unitTo avoid SERIOUS damage to garage door opener,use ONLY those bolts/fasteners mounted in thetop of the
7AssemblySTEP 4 Install the belt1. Pull the beltaround the idler pulley and toward the trolley.The ribbed side must contact thepulley.2. Hook the trol
8AssemblySTEP 5 Tighten the belt1. Byhand, thread the spring trolley nut on the threaded shaftuntil itis finger tight againstthetrolley.Do not use any
Comments to this Manuals