Chamberlain 1280 - 1/2 HP User Manual download pdf (Page 14)

Opener

Terminal Screws

Antenna

Right Panel

of Opener

Multi-Function

Door Control Panel

Multi-Function

Door Control Panel

Terminal Screws

WHITE

RED

The Chamberlain Group, Inc.

Liftmaster Belt Drive CDO

Install Wall Control

3/5/92 - 3/13/92

LIGHT

LOCK

Door Control

Button

Light Button

Lock Button

M.D.C. CERT. NO.

132C2105-1

WARNING: To reduce the risk of severe injury

or death by entrapment, when adjusting either

the force or limits of travel controls ensure that

the door reverses on a 1 inch object (or a 2 x 4

board laid flat). See instructions for proper

adjustment procedure.

This device complies

with FCC Rules Part

15. Operation of this

device is subject to the

following conditions:

1. This device may

not cause harmful

interference. 2. This

device must accept

any interference

that may be received,

including interference

that may cause

undesired operation.

PART NO: Nº DE PIÈCE:

D.O.C. CERT. NO.

DATE:

PAT. #RE29,525; 4,750,201; 4,806,930 Other Patents Pending.

AVERTISSEMENT: Pour réduire les risques de

blessures mortelles par happement, après tout

réglage de la force de déclenchement ou des

seuils de fin de course s'assurer que le sens de

la course s'inverse lorsque la porte entre en

contact avec un object de 13 mm (1 po) de

hauteur (ou un madrier de 2 x 4 de section, à

plat) posé sur le sol. Effectuer les reglages

selon les procédures décrites dans la notice.

2 3

TO PROGRAM RECEIVER CODE

FOR EACH REMOTE CONTROL

1. Press and HOLD remote control

transmitter push button.

2. Press receiver code button. The opener

light will flash once.

3. Release transmnitter button. Opener

has learned code.

TO ERASE ALL RECEIVER CODES

1. Press and HOLD receiver code button.

Green indicator light alongside will turn

ON.

2. When light turns OFF (about 6

seconds) ALL codes are erased from

opener memory.

Installation Step 6

Install the Multi-Function

Door Control Panel

Children operating or playing with a garage

door opener can injure themselves or others.

The garage door could close and cause

serious injury or death.

Install the door control

(or any additional push buttons) out of the

reach of children and away from all moving

parts of the door and door hardware,

but

where the garage door is visible.

Do not allow

children to operate the push button(s) or the

remote control transmitter(s).

A moving garage door could injure someone

under it.

Activate the opener only when the

door is properly adjusted, you can see it clearly,

and there are no obstructions to door travel.

• Strip 1/4" of insulation from one end of the bell

wire; connect the wire to the two screw terminals

on the back of the door control by color: white to 2

and white/red to 1.

• Locate the door control within sight of the door

at a minimum height of 5 feet where small

children cannot reach, and away from all

moving parts of the door and door hardware.

Fasten the Multi-Function Door Control securely

with 6ABx1" screws. If installing into drywall, drill

5/32" holes and use the anchors provided.

• Run the bell wire up the wall and across the ceiling

to the opener. Use insulated staples to secure the

wire in several places. Be careful not to pierce the

wire with a staple, creating a short.

• Receiver terminal screws and the antenna are

located on the right panel of the opener. Position

the antenna wire as shown.

• Then connect the bell wire to the opener terminal

screws: white to 2 and white/red to 1.

• Remember to affix the User Safety Instruction

label to the wall near the door control, and the

Maintenance Instruction label in a prominent

location on the inside of the garage door.

If the label adhesive will not adhere to your garage

wall surface (or becomes loose with time) use tacks

to secure the label alongside the door control.

Page 28 explains how to operate the opener using

the lighted push button and the Lock & Light

features available on the Multi-Function Door

Control Panel.

Dry Wall Anchors



Insulated 

Staples

6AB x 1" Screw

Multi-Function Door Control

Hardware Shown Actual Size

Outside Keylock Accessory Connections

To opener terminal screws: white to 2; white/red to 1

WARNING

Do NOT connect the power and operate the

opener at this time.

The trolley will travel to the

full

open

position but will not return to the

position until the sensor beam is

connected and properly aligned.

See Safety Reversing Sensor Instructions

beginning on page 17.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 35 36

Comments to this Manuals

No comments

Chamberlain 1280 - 1/2 HP User Manual Page 14

Comments to this Manuals

Related products and manuals for Kitchen Chamberlain 1280 - 1/2 HP