Garage Door OpenerFor Residential Use Only(Model Series 1200 - Canada )Model 1260 - 1/2HPModel 1250 - 1/3HPModel 1255 - 1/2HPModel 1245 - 1/3HP®O
UPLag Screws5/16"x18x1-7/8"GarageDoorVerticalCenter LineHeaderWallFinishedCeilingHeaderBracket6" MaximumVerticalCenter LineDoor
HeaderBracketChainPulleyBracketTemporarySupportHeader WallGarageDoorT-railClevis Pin5/16"x2-3/4 "Ring FastenerHeader BracketChainPulleyBrack
Installation Step 4Position the OpenerFollow instructions which apply to your door typeas illustrated.To prevent damage to steel, aluminum,fiberglass
Installation Step 5Hang the OpenerTwo representative installations are shown.Yours may be different. Hanging brackets shouldbe angled, Figure 1, to pr
Installation Step 6Install the Door Control 14Children operating or playing with a garagedoor opener can injure themselves or others.The garage door c
Lens Slot75 Watt Max.Light BulbLens TabLightLens ScrewPanelInstall the light(s)• Install a 75 watt maximum light bulb in eachsocket. The light(s) will
To reduce the risk of electric shock, your garagedoor opener has a grounding type plug with a thirdgrounding pin. This plug will onlyfit into a ground
The safety reversing sensor mustbe connectedand aligned correctly before the garage dooropener will move in the down direction. This is arequired safe
1/4x1-1/2"Lag Screw#10-32x3/8"Screw1/4"-20Lock Nut#10x32Lock NutStaples1/4"-20x1/2"Carriage BoltsInstallation Step
Invisible Light BeamProtection AreaSensorSensorConnect Wire toOpener TerminalsBell WireBell WireFinishedCeilingOPENER TERMINAL SCREWSSensorConnections
Start by reviewing these important safety alert symbols2CONTENTS PAGEA review of safety alert symbols ...2You'll need
Installation Step 11Fasten Door Bracket Follow instructions which apply to your door typeas illustrated below or on page 21.To prevent damage to ste
Horizontal and verticalreinforcement is needed forlightweight garage doors(fiberglass, aluminum, steel, door with glass panel, etc.).Header WallVe
Installation Step 12 Connect Door Arm to TrolleyFollow instructions which apply to your door typeas illustrated below and on page 23.Make sure garage
All ONE-PIECE DoorsAssemble the Door Arm:• Fasten the straight and curved door arm sectionstogether to the longest possible length (with a 2 or3 hole
Adjustment Step 1Adjust the UP and DOWN LimitsDo not make any limit adjustments until thesafety reversing sensors are completelyinstalled.24Limit adju
Adjustment Step 2Adjust the ForceToo much force on the door will interfere withthe proper operation of the safety reversesystem. The door might not re
Adjustment Step 4Test the Safety Reverse SystemTest:• Place a 2x4 laid flat on the floor, centered underthe garage door.• Operate the door in the down
The remote control transmitter:The opener must learn the code of any new remotecontrol. Page 29 explains how to program yourreceiver and how to erase
28Operation of Your OpenerTo open the doormanually:The door should befully closed if possible. Pull down onthe red manualrelease handle and liftthe do
Children operating or playing with a garagedoor opener can injure themselves or others.The garage door could close and causeserious injury or death.Do
PliersWire CuttersClaw HammerHack SawScrewdriverAdjustable End Wrench1/2" and 7/16" Socketsand WrenchDrillTape Measure21StepladderPencil3/16
1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light,check the fuse box or the circuit breaker. (Some outlets
The chain droopsor sags:It is normal for the chain to droop slightly in the closed door position. Use the manualrelease rope and handle to disconnect
10UPCEILING MOUNT ONLY7121412VDC3LIGHTLOCK1245NOTICE6981113151621345RAIL GREASENO. 83A46Rail Assembly PartsInstallation Parts32KEY PARTNO. NO. DESCRIP
Repair PartsOpener Assembly Parts1211914151617205463DNUPBrownWire(Down)ContactLIMIT SWITCH ASSY.GreyWireYellowWire(Up)ContactCenter LimitContactDriveG
1 23 45 67 89 0ENTERLIGHTLOCKModel 58LMCModel 64LMCModel 99LMCModel 60LMCMulti-Function Mini RemoteControl:With key ring & Velcro fasteningst
IndexAccess Door/Outside Quick Release Accessory...4, 34Electri
LIFT-MASTER SERVICEIS ON CALLOUR LARGE SERVICE ORGANIZATIONSPANS AMERICA AND CANADAINSTALLATION AND SERVICE INFORMATION IS ASNEAR AS YOUR TELEPHONE SI
4Safety Reversing SensorHorizontal and vertical reinforcementis needed for lightweight garage doors(fiberglass, steel, aluminum, door with glass panel
5Straight DoorArm SectionDoor Bracket Plate Door BracketCurved DoorArm SectionSafety LabelsandLiteratureHeader BracketUPCEILING MOUNT ONLYSafety Rever
Assembly Step 1Attach the T-rail to the OpenerTo fasten rail, use only those screws mountedin top of the opener. Failure to do so will causeserious da
Assembly Step 3Tighten the Chain7IMPORTANT INSTALLATION INSTRUCTIONSTo reduce the risk of severe injury or death to persons:1. READ AND FOLLOW ALL IN
• Open your door to the highestpoint of travel as shown. Drawan intersecting horizontal lineon the header wall 2" abovethe high point. This heigh
9Header WallVerticalCenterlineVerticalCenterline ofGarage Door2x4UnfinishedCeilingStructuralSupports2x4OPTIONAL CEILING MOUNTFOR HEADER BRACKET• Close
Comments to this Manuals