Doc. 6001194 (01Doc. 6001194 (01Doc. 6001194 (01Doc. 6001194 (01----20259)20259)20259)20259) Rev CRev CRev CRev C INSTALLATION
Rev C Doc 6001194 (01-20259) 7 of 36 WARNING For safety reasons, the Power Fail Operation Option is shipped with the battery unconnnected to the
Rev C Doc 6001194 (01-20259) 8 of 36 B. CONNECTING POWER Figure 11. AC Wiring. C. RUNNING INPUT WIRING 1. Remove the plastic control box cove
Rev C Doc 6001194 (01-20259) 9 of 36 E. POWER UP PROCEDURE CAUTION If gate is positioned at the ‘open’ limit, gate will automatically close when
Rev C Doc 6001194 (01-20259) 10 of 36 Figure 14. Limit Cam Setting. NOTE: The following procedures are for FRONT drive gates. For MID and REA
Rev C Doc 6001194 (01-20259) 11 of 36 NOTES: 1. Overload setting (R72) is factory set. Do not adjust. 2. Current flow varies with temperature
Rev C Doc 6001194 (01-20259) 12 of 36 "OPEN TO LEFT" ADJUSTMENT PROCEDURES Left Gate Motion Adjustment (R160) 1. Initiate opening the
Rev C Doc 6001194 (01-20259) 13 of 36 J. POWER FAIL OPERATION OPTION CONNECTION a) Power Fail Operation Option Connection CAUTION Perform the n
Rev C Doc 6001194 (01-20259) 14 of 36 K. CONNECTING INPUT WIRING Figure 16. Control Board Wiring. 1. Remove the plastic control box cover. 2.
Rev C Doc 6001194 (01-20259) 15 of 36 L. POST INSTALLATION PROCEDURES 1. Setup 1. Turn on the main power at the gate operator's circuit b
Rev C Doc 6001194 (01-20259) 16 of 36 7. Alternate Action 1. If you want the OPEN input (Entry system) or RADIO input (Transmitter) to both ope
Rev C Doc 6001194 (01-20259) TABLE OF CONTENTS SAFETY SUMMARY...
Rev C Doc 6001194 (01-20259) 17 of 36 M. FINAL ASSEMBLY OF GATE OPERATOR Figure 17. Gate Operator Final Assembly IMPORTANT SAFETY PROCEDURE ⇒
Rev C Doc 6001194 (01-20259) 18 of 36 PART 3 MODEL SL 1000-X1 OPTIONS POWER FAIL OPERATION OPTION The LiftMaster Power Fail Operation Option ma
Rev C Doc 6001194 (01-20259) 19 of 36 PART 4 TROUBLESHOOTING AND MAINTENANCE A. TROUBLESHOOTING This section is designed to help you troublesh
Rev C Doc 6001194 (01-20259) 20 of 36 4. THE CONTROL BOARD RESETS RIGHT AFTER GATE STARTS MOVING 1. Low AC voltage. 2. Inadequate and undersiz
Rev C Doc 6001194 (01-20259) 21 of 36 13. GATE DOES NOT CLOSE AUTOMATICALLY 1. Reclose timer setting is disabled. 2. The entry system is conne
Rev C Doc 6001194 (01-20259) 22 of 36 22. THERE IS SLACK IN THE GATE 1. Chain is too loose. 2. The hardware interconnecting the operator to th
Rev C Doc 6001194 (01-20259) 23 of 36 B. FAULT LIST The following conditions can cause a fault in the SL 1000-X1 gate operator system: 1. Safet
Rev C Doc 6001194 (01-20259) 24 of 36 3. IF MAX RUN TIME LED IS TURNED ON ONLY 1. Limit cams do not engage the limit switches. 2. The belt or
Rev C Doc 6001194 (01-20259) 25 of 36 D. MAINTENANCE WARNING To avoid injury, always turn off the unit power switch before working on gate. Regu
Rev C Doc 6001194 (01-20259) 26 of 36 PREVENTIVE MAINTENANCE INSTRUCTIONS Figure 18. Gate Operator Disassembly and Assembly. Gate Operator Ser
Rev C Doc 6001194 (01-20259) The Model SL 1000-X1 The LiftMaster model SL 1000-X1 Slide Gate Operator is a full featured, commercial gate operator
Rev C Doc 6001194 (01-20259) 27 of 36 The following table was provided to help you keep a record of the maintenance schedule. Write the inspecti
Rev C Doc 6001194 (01-20259) 28 of 36 APPENDIX A SYSTEM OPERATION REFERENCE CONTROLS, INDICATORS, INPUTS AND ADJUSTMENTS For control and indic
Rev C Doc 6001194 (01-20259) 29 of 36 CONTROLS KEYPAD The 12-key keypad is used for local operation, programming and service. SWITCH S1 GATE OPE
Rev C Doc 6001194 (01-20259) 30 of 36 FUNCTIONAL INPUTS NOTES: ➊ The term "activation" means closing an input circuit (via a relay or
Rev C Doc 6001194 (01-20259) 31 of 36 SAFETY BAR Activation causes the gate to reverse for a programmable distance and stop. If Max Retry Count
Rev C Doc 6001194 (01-20259) 32 of 36 APPENDIX B MODEL SL 1000-X1 PARTS LIST ITEM # PART NAME WHAT IT DOES 1 Control Box/Clear Cover Cont
Rev C Doc 6001194 (01-20259) 33 of 36 APPENDIX C PARALLEL WIRING GATE OPERATORS In the absence of Master/Slave firmware, two SL 1000-X1s may b
Rev C Doc 6001194 (01-20259) 34 of 36 GLOSSARY AC: Alternating Current. An electric current or voltage that reverses direction at regular inte
Rev C Doc 6001194 (01-20259) 35 of 36 NOTICE TO CANADIAN USERS NOTICE: The Industry Canada label identifies certified equipment. This certificat
COPYRIGHT 2001 ALL RIGHTS RESERVED This document is protected by copyright and may not be copied or adapted without the prior written consent o
Rev C Doc 6001194 (01-20259) 1 of 36 SAFETY SUMMARY It is imperative that everyone involved in the installation or operation of the LiftMaster mo
Rev C Doc 6001194 (01-20259) 2 of 36 BASIC INSTALLATION HINTS AND RULES PLEASE READ THIS SECTION VERY CAREFULLY BEFORE BEGINNING YOUR INSTALLATIO
Rev C Doc 6001194 (01-20259) 3 of 36 PART 1 SITE PREPARATION A. LOCATION AND LAYOUT Figure 1. Front Drive. Figure 2. Rear Drive
Rev C Doc 6001194 (01-20259) 4 of 36 B. PAD AND MOUNT Figure 4. Pad And Track Ribbon. Figure 5. Bolt Down Pattern. Figure 6. Con
Rev C Doc 6001194 (01-20259) 5 of 36 C. POWER WIRING 1. Provide a conduit stub for the AC power. 2. The gate operator requires a 115 VAC 20 AM
Rev C Doc 6001194 (01-20259) 6 of 36 PART 2 SYSTEM INSTALLATION A. MOUNTING GATE OPERATOR Figure 7. Mounting. Figure 8.
Comments to this Manuals