Chamberlain 379LMC-10 User Manual download pdf

To prevent possible SERIOUS INJURY or DEATH from a

moving gate or garage door:

• Install Keyless Entry Control within sight of the garage door,

out of reach of children at a minimum height of 5 feet

(1.5 m), and away from ALL moving parts of door.

• ALWAYS keep remote controls out of reach of children.

NEVER permit children to operate, or play with remote

control transmitters.

• Activate gate or door ONLY when it can be seen clearly, is

properly adjusted, and there are no obstructions to door

travel.

• ALWAYS keep gate or garage door in sight until completely

closed. NEVER permit anyone to cross path of moving gate or

door.

Model 379LM-10 and 379LMC-10

Fingerprint Keyless Entry

Overview

For use with any 315 MHz SECURITY®

garage door openers

having a purple "learn" button (refer to Step 4.)

The system uses biometric technology that enables an

authorized user to gain access by scanning their ﬁ ngerprint.

The sensor strip on the unit makes a numeric template of the

ﬁ ngerprint that is unique to that user. The unit’s memory can

store up to ten ﬁ ngerprints.

• The term “enroll” refers to scanning the ﬁ ngerprint so the

device will recognize the user.

• The term “swipe” refers to the movement of the ﬁ nger across

the sensor strip.

• The term “LED” stands for Light Emitting Diode. There are 6

LEDs located on the Fingerprint Keyless Entry.

When unit is on, it is programmed to shut off after a short period

of time. The unit’s sensor strip is sensitive so it is important to

read the Tips for Success before attempting to use the

Fingerprint Keyless Entry.

Step 1 Install the Unit

1. Remove cover.

2. Fasten bottom screw to mounting surface. Allow 1/8" (3 mm)

to protrude above surface. Position unit on screw head and

adjust for snug ﬁ t.

3. Fasten top screw. Replace cover.

Tips for Success

CORRECT

1. Make sure ﬁ nger is clean and dry.

Place ﬁ nger ﬂ at above the sensor strip

with the top knuckle above the sensor.

2. Swipe ﬁ nger straight down keeping

ﬁ rm contact with the sensor. The swipe

should be a slow, constant speed.

SPECIAL NOTES: Use the same ﬁ nger for

every swipe. It is important to swipe ﬁ nger slowly and ﬁ rmly as

this is the reason most swipes fail.

NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modiﬁ cations of

this receiver and/or transmitter are prohibited, except for changing the code setting or replacing

the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.

Tested to Comply with FCC Standards for Home or ofﬁ ce use. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

Sensor Strip

Start swipe with

the top knuckle

above the

sensor strip.

The scan

should end

at the tip of

finger.

Swipe finger straight down

keeping firm contact with

the sensor.

INCORRECT

• Do not bend ﬁ nger during swipe as this will only scan the tip of

your ﬁ nger.

• Swipe ﬁ nger straight down, not at an angle.

• Swipe ﬂ at, not tilted or rolled to one side.

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Fingerprint Keyless Entry

To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:• Install Keyless Entry Control within sight of the garage door, out of

Page 2 - Reference

Step 2 Enroll Initial UserNOTE: The unit requires 3 passed swipes to enroll a user.1. Open cover to turn unit on. Wait until Enroll LED and Ready LED

Page 3 - Step 4 Program to Opener

NOTE: The unit must have an enrolled user before it can be programmed to the opener. Due to the 30 second time interval, a second person may be neede

Page 4 - The Battery

• To return to Factory Reset state:NOTE: Factory reset state will erase ALL stored ﬁ ngerprints. This method should be used ONLY when an enrolled user

Page 5 - AVERTISSEMENT

Aﬁ n d’éliminer les risques de BLESSURES GRAVES ou de MORT découlant de l’actionnement d’une clôture ou d’une porte de garage :• Poser la commande d

Page 6 - Referencía

Étape 2 Inscription de l’utilisateur initialREMARQUE : Pour inscrire un utilisateur, l’appareil requiert 3 passages réussis.1. Ouvrez le couvercle po

Page 7 - Étape 5 Fonctionnement

REMARQUE : L’appareil doit avoir un utilisateur inscrit avant d’être programmé au dispositif d’ouverture. Étant donné l’intervalle de 30 secondes, une

Page 8

• Pour restaurer les paramètres usine de l’appareil :REMARQUE : La restauration des paramètres usine supprimera TOUTES les empreintes digitales mémori

Comments to this Manuals

No comments

Chamberlain 379LMC-10 User Manual

Browse online or download User Manual for Unknown Chamberlain 379LMC-10. Chamberlain 379LMC-10 User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Unknown Chamberlain 379LMC-10