Chamberlain SECURITY HD200DM User Manual

The Chamberlain Group, Inc.845 Larch AvenueElmhurst, Illinois 60126-1196www.chamberlain.comGARAGE DOOR OPENER Model HD200DM • 1/2 HPFor Residential Us

10To avoid possible SERIOUS INJURY to fingers from moving garage door opener:• ALWAYS keep hand clear of sprocket while operating opener.• Securely a

11INSTALLATIONASSEMBLY STEP 5Tighten the Chain • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley.• To tigh

12INSTALLATION STEP 1Determine the Header Bracket LocationInstallation procedures vary according to garage door types. Follow the instructions which a

13Lag Screws5/16"x9x1-5/8"– Finished Ceiling –DoorSpringHeader WallUPCeiling Mounting Holes6" (15 cm) MaximumHeaderBracketVerticalCente

14INSTALLATION STEP 3Attach the Rail to the Header BracketNOTE: (Optional) With some existing installations, you may re-use the old header bracket wit

15ONE-PIECE DOOR WITHOUT TRACKA 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging.• Raise the opener

16INSTALLATION STEP 5Hang the OpenerThree representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1)

17To prevent possible SERIOUS INJURY or DEATH from electrocution:• Be sure power is not connected BEFORE installing door control.• Connect ONLY to 2

18INSTALLATION STEP 7Install the Light• Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in

19INSTALLATION STEP 9Electrical RequirementsTo avoid installation difficulties, do not run the opener at this time.To reduce the risk of electric shoc

2TABLE OF CONTENTSWhen you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury

20Invisible Light BeamProtection AreaSafety Reversing Sensor6" (15 cm) max. above floorSafety Reversing Sensor6" (15 cm) max. above floorFac

21DOOR TRACK MOUNT (RIGHT SIDE)IndicatorLightLensLip SensorBracketDoorTrackFLOOR MOUNT (RIGHT SIDE)WALL MOUNT (RIGHT SIDE)IndicatorLightSensorBracketL

22Carriage Bolt 1/4"-20x1/2"LensWing Nut1/4"-20Figure 5MOUNTING AND WIRING THE SAFETY REVERSING SENSORS• Slide a 1/4"-20x1/2"

23Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacture

24Header WallVerticalCenterline ofGarage DoorFinished Ceiling OptionalPlacementof DoorBracketHeaderBracketDoorBracket2x4 SupportFor a door with no exp

25INSTALLATION STEP 12Connect Door Arm to TrolleyFollow instructions which apply to your door type as illustrated below and on the following page.SECT

26ALL ONE-PIECE DOORS1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (

27ADJUSTMENT STEP 1Adjust the UP and DOWN Travel LimitsLimit adjustment settings regulate the points at which the door will stop when moving up or dow

Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage do

29Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage

3To prevent damage to garage door and opener:• ALWAYS disable locks BEFORE installing and operating the opener. • ONLY operate garage door opener at

30OPERATION Using Your Garage Door OpenerYour Security✚® opener and hand-held remote control have been factory-set to a matching code which changes wi

31To Open the Door ManuallyDISCONNECT THE TROLLEY:The door should be fully closed if possible. Pull down on the emergency release handle (so that the

32CARE OF YOUR OPENERLIMIT AND FORCE ADJUSTMENTS:Weather conditions may cause some minor changes in door operation requiring some re-adjustments, part

33HAVING A PROBLEM?1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned co

34Installed Safety Reversing SensorSafety Reversing SensorBell WireDiagnosticsLocated On Motor UnitLED or Diagnostic LED"Learn" Button Your

*3-Button Remotes (315 MHZ)If provided with your garage door opener, the large button is factory programmed to operate it. Additional buttons on any S

361. Press and release the “learn” button on motor unit. The learn indicator light will glow steadily for 30 seconds.2. Within 30 seconds, enter a f

791011NOTICE56814121332315426Installation Parts37REPAIR PARTSRail Assembly PartsKEY PART NO. NO. DESCRIPTION1 4A1008 Master link kit2 41C5141-1

Motor Unit Assembly Parts3821081314151945391612181117167DNUPBrownWire(Down)ContactLIMIT SWITCHASSEMBLYGreyWireYellowWire(Up)ContactCenter LimitContact

39ACCESSORIES LOCK LIGHT CLOSED OPEN LOCK LIGHT 3-Button SECURITY✚® Remote Control :Includes visor clip.SECURITY✚® Keyless Entry :Enables homeowne

4Safety Reversing SensorHorizontal and vertical reinforcementis needed for lightweight garage doors(fiberglass, steel, aluminum,door with glass panels

© 2008, The Chamberlain Group, Inc.114A3591 All Rights ReservedCHAMBERLAIN SERVICE IS ON CALLOUR LARGE SERVICE ORGANIZATION SPANS AMERICAINSTALLATI

5AccessDoorSafetyReversing SensorSafetyReversingSensorGap between floor and bottom of doormust not exceed 1/4" (6 mm).DoorBracketStraightDoorArmG

62-Conductor Bell WireWhite & White/RedChain and Cable inDispensing CartonCurved DoorArm SectionStraight DoorArm SectionSafety LabelsandLiterature

7Wing Nut 1/4"-20 (2) Handle Nut 5/16"-18 (8) Ring Fastener (3) Spacer (2) Carriage Bolt 1/4"-20x1/2" (2) Insulated Staples (30)

FRONT RAIL(TOP)KEEP LARGERHOLE ON TOP8ASSEMBLY STEP 1Assemble the Rail & Install the TrolleyTo avoid installation difficulties, do not run the gar

9To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of the opener.ASSEMBLY STEP 2Fasten the Rail to the