Chamberlain WD962KLD User Manual download pdf (Page 17)

INSTALLATION STEP 6

Install the Door Control

Locate door control within sight of door, at a minimum

height of 5 feet (1.5 m) where small children cannot reach,

away from moving parts of door and door hardware.

If installing into drywall, drill 5/32" holes and use the

anchors provided. For pre-wired installations (as in new

home construction), it may be mounted to a single gang

box (Figure 2).

1. Strip 7/16" (11 mm) of insulation from one end of bell

wire and connect to the two screw terminals on back of

the door control by color: white wire to 2 and white/red

wire to the 1.

2. Remove cover by gently prying at slot in top of the

cover with a small ﬂ at head screwdriver. Fasten with

6ABx1-1/4" self-tapping screws (drywall installation) or

6-32x1" machine screws (into gang box) as follows:

• Install bottom screw, allowing 1/8" (3 mm) to

protrude above wall surface.

• Position bottom of the door control on screw head

and slide down to secure. Adjust screw for snug ﬁ t.

• Drill and install top screw with care to avoid

cracking plastic housing. DO NOT overtighten.

• Insert top tabs and snap on cover.

3. (For standard installation only) Run bell wire up wall

and across ceiling to motor unit. Use insulated staples

to secure wire in several places. DO NOT pierce wire

with a staple, creating a short or open circuit.

4. Strip 7/16" (11 mm) of insulation from end of bell wire.

Connect bell wire to the quick-connect terminals as

follows: white to white and white/red to red.

5. Position the antenna wire as shown.

6. Use tacks or staples to permanently attach entrapment

warning label to wall near door control, and manual

release/safety reverse test label in a prominent location

on inside of garage door.

NOTE: DO NOT connect power and operate opener at

this time. The trolley will travel to the full open position but

will not return to the close position until the sensor beam

is connected and properly aligned.

To prevent possible SERIOUS INJURY or DEATH from

electrocution:

• Disconnect ALL electric and battery power BEFORE

performing ANY service or maintenance.

• Connect ONLY to 24 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from

a closing garage door:

• Install the door control within sight of garage door,

out of reach of children at a minimum height of

5 feet (1.5 m), and away from ALL moving parts

of door.

• NEVER permit children to operate or play with the

door control push buttons or remote controls.

• Activate door ONLY when it can be seen clearly, is

properly adjusted, and there are no obstructions to

door travel.

• ALWAYS keep garage door in sight until completely

closed. NEVER permit anyone to cross path of

closing garage door.

HARDWARE SHOWN ACTUAL SIZE

Figure 1 Figure 2

To Replace

Insert Top

Tabs First

To Replace

Insert Top

Tabs First

Terminal

Screws

Top

Mounting

Hole

Door Control Connections

Strip wire 7/16" (11 mm)

To insert or release wire, push

in tab with screwdriver tip

Red White Grey

Bell

Wire

(BACK VIEW)

Bottom

Mounting

Hole

Push Bar

Cover

Push Bar

Cover

Detector

Switch

OFF

Detector

Switch

24 Volt

Bell Wire

STANDARD WALL MOUNT PRE-WIRED INSTALLATION

Screw 6ABx1-1/4"

(Standard Installation)

Drywall Anchors

Insulated Staples

Screw 6-32x1" (pre-wired)

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 43 44

Comments to this Manuals

No comments

Chamberlain WD962KLD User Manual Page 17

Comments to this Manuals

Related products and manuals for Kitchen Chamberlain WD962KLD